 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MHP TO-247 Series Power Resistor MHP TO-247 Series * TO-247 housing * Low inductance (<50nH) * Available in 100W or 140W * High stability film resistance elements * RoHS compliant terminations * Insulated metal back plate * Approved to DSCC drawing 07019 IRC's MHP series resistors satisfy demanding applications for accurate and stable power resistors housed in the convenient TO-247 case. The resistance element is isolated from the mounting tab by an alumina ceramic layer, providing very low thermal resistance and ensuring high insulation resistance between terminals and metal back plate. The non-inductive design makes these products especially useful in high frequency and high speed pulse applications. Electrical Data Type Power Rating1 Heatsink2 Free Air3 MHP100LF 100W 3W Voltage Rating4 Thermal Resistance Resistance Range Min 0.01 700V 1.3C/W 0.1 10 0.01 MHP140LF 1 Tolerances 5% 1%, 5% 1%, 5% 5% 1%, 5% 1%, 5% Max 0.09 9.1 51K 0.09 9.1 51K Nominal Resistance E6 E12 E24 E6 E12 E24 Typ. Temperature Coefficient5 250 ppm/C 100 ppm/C 50 ppm/C 250 ppm/C 100 ppm/C 50 ppm/C 140W 3W 700 V 0.9C/W 0.1 10 Maximum current 25 amps 2 Power rating based on 25C case temperature 3 Power rating based on 25C ambient temperature 4 Maximum voltage 700V or P x R 5 See TCR Chart for resistance values below 1ohm Pulse Energy Durability 100K MHP100/140LF R200 J to MHP100/140LF 100R F 1K Frequency Characteristics MHP100/140LF 1K0 F Pulse Peak (Watts) 10K Damage Level Impedance (ohms) 100 MHP100/140LF 100R F 1K Safety Zone 100 100n 10 MHP100/140LF 10R0 F 1 1 10 100 1m 10m 10K 100K 1M 10M 100M 1G Pulse Width (seconds) Frequency(Hz) General Note IRC reserves the right to make changes in product specification without notice or liability. All information is subject to IRC's own data and is considered accurate at time of going to print. Advanced Film Division * 4222 South Staples Street * Corpus Christi Texas 78411 USA Telephone: 361 992 7900 * Facsimile: 361 992 3377 * Website: www.irctt.com A subsidiary of TT electronics plc MHP TO-247 Series Issue May 2009 MHP TO-247 Series Power Resistor Physical Data C L Note: Metal tab is electrically isolated. C L Dim F In (nom) 0.630 0.787 0.189 0.126 0.571 0.201 0.143 0.032 0.032 0.429 mm 16.0 0.2 20.0 0.5 4.8 0.2 3.2 0.1 14.5 0.5 5.1 0.5 3.63 0.2 0.8 0.05 0.8 0.05 10.9 0.1 A B C L OD B C OD E F G K E H J G H A J C K Lead Material Tab Material Tin Plated Copper Nickel Plated Copper Environmental Data Test Thermal Shock Moisture Resistance Vibration Load Life Resistance to Solder Heat Dielectric Withstanding Voltage Insulation Resistance (between terminal and tab) Solderability Operating Temperature Range * During soldering, the soldering temperature profile must not cause the metal tab of this device to exceed 220C. Advanced Film Division * 4222 South Staples Street * Corpus Christi Texas 78411 USA Telephone: 361 992 7900 * Facsimile: 361 992 3377 * Website: www.irctt.com Method MIL-STD-202 Method 107 Condition F MIL-STD-202 Method 106 MIL-STD-202 Method 204 Condition D MIL-STD-202 Method 108 1,000 Hours MIL-STD-202 Method 210 Condition B MIL-STD-202 Method 301 MIL-STD-202 Method 302 230 5C, 3sec. Specification - Performance 0.30% + 50m 1.0% + 50m 0.25% + 50m 1.0% + 50m 0.25% + 50m 2200 volts DC or 2500 volts AC; 60 seconds >1000M> >75% coverage -55C to +155C MHP TO-247 Series Issue May 2009 MHP TO-247 Series Power Resistor Power Derating Data 100 140 120 Tfilm (C) Temperature Rise Data Resistor Film Temp Rise with Respect to Flange Temp MHP100 MHP140 % of Rated Power 100 80 60 40 20 0 0 50 10 25 Flange Temperature (C) 155 20 40 60 80 Power (Watts) 100 120 140 Typical TCR For Low Values TCR (ppm/C) 0 to 100C 250 200 150 100 50 0 0.01 0.1 Resistance (Ohms) 1.0 Application Notes: 1. Insulating material is unnecessary between the heat sink and the tab, as the resistor film is isolated by the internal alumina substrate. 2. When mounting with a fastener, thermal grease is recommended. 3. Thermal design should satisfy the following equation: Case Temperature (Tc) + [Thermal Resistance (ROJC) x Power applied (Watts)] 155C over the full operating temperature of the application. 4. Resistor film temperature is not to exceed 155C during operation. 5. This product is RoHS compliant by exemption according to RoHS directive 2002/95/EC exemptions 5 & 7, as they apply to lead in glass and internal solder connections. Ordering Data Prefix Style TFP - MHP100LF - 1R50 - J MHP100LF = 100W, TO-247 style power resistor 07019 = DSCC drawing (07019) ver. of above MHP140LF = 140W, TO-247 style power resistor Resistance Code 4-digit resistance code. Ex: 10R0 = 10, 1K00 = 1K Absolute Tolerance Code J = 5%; F = 1% Standard Packaging RoHS compliant PE tray (50 pcs per tray) For additional information or to discuss your specific requirements, please contact our Applications Team using the contact details below. Advanced Film Division * 4222 South Staples Street * Corpus Christi Texas 78411 USA Telephone: 361 992 7900 * Facsimile: 361 992 3377 * Website: www.irctt.com MHP TO-247 Series Issue May 2009 |
Price & Availability of TFP-MHP100LF-10R0-F
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |